Glossary
Pressure class
Loonar · Updated 12 November 2026
A pressure class is a dimensionless designation, such as Class 150, 300 or 600, that sets the pressure-temperature rating of flanges and valves under ASME B16.5 and ASME B16.34, and the flange dimensions. The allowable pressure depends on the class, the material group and the temperature. "ANSI 300" is an older name for Class 300.
Also called: ASME class, ANSI class, pressure rating class, Class 300.
What a pressure class sets
- The rating. The class determines the maximum allowable working pressure at each temperature, read from the table for the material group of the body or flange.
- The flange dimensions. For flanges to ASME B16.5, the class affects thickness, outside diameter and bolting. In small sizes, some neighbouring classes share the bolting but not the thickness.
- Not the face-to-face length by itself. For flanged valves, face-to-face and end-to-end dimensions are set separately, mainly by ASME B16.10, and depend on valve type, size and class.
ASME B16.5 covers flange classes 150, 300, 400, 600, 900, 1500 and 2500. ASME B16.34 sets the pressure-temperature ratings, design, testing and marking of valves. It also has a Class 4500, which applies to welding-end valves only.
Rating values: the class is not a pressure
For carbon steel of material group 1.1, such as forged ASTM A105 or A350 LF2 and cast A216 WCB, the ASME B16.5 rating at −29 to 38 °C is:
| Class | Rating at −29 to 38 °C | Approximate bar |
|---|---|---|
| 150 | 285 psi | 19.6 |
| 300 | 740 psi | 51 |
| 600 | 1,480 psi | 102 |
| 900 | 2,220 psi | 153 |
| 1500 | 3,705 psi | 255 |
| 2500 | 6,170 psi | 425 |
Values from the Group 1.1 table of ASME B16.5 in psi, with bar figures rounded. The metric tables of different editions differ in the first decimal. Always check the ratings against the edition named in the project documents.
The allowable pressure falls as temperature rises, along the table of each material group. Other groups, such as stainless steels or low-temperature cast grades, have their own tables. Always read the table for the actual material and the actual design temperature.
How the class is chosen
The pressure class is normally set by the piping material specification, or piping class, of each line, from its design pressure and temperature. Valves and flanges on the line must meet it, together with any equipment-specific specification. The valve datasheet normally repeats the class of the piping class.
When the two disagree, the conflict is real: a valve rated below the line, or a valve that does not fit the flanges. It is a question for the buyer, raised as a clarification and read against the tender's order of precedence.
Same class, different allowable pressure
A material substitution can keep the class and still change the rating. Forged ASTM A350 LF2 and cast A352 LCC are both used for low-temperature service, subject to their material specifications and impact-test requirements. But ASME B16.34 assigns them to different material groups: LF2 to Group 1.1, LCC to Group 1.2. At ambient temperature, a Class 600 rating is 1,480 psi in LF2 and 1,500 psi in LCC.
A supplier who offers LF2 where the datasheet names LCC declares it as a technical deviation and confirms the rating against the design pressure and temperature.
Pressure class in a tender package
The class appears in several documents of the same package: the valve datasheet, the piping class, the line list, sometimes the P&ID. In a tender, check that they agree, line by line. Then check what the class implies:
- the material group and its rating at the design temperature;
- the flange facing, such as raised face or ring-type joint, which the class does not set by itself;
- the test pressures of the valve, which follow from the rating;
- for valves, Standard Class or Special Class. ASME B16.34 Special Class ratings carry additional non-destructive examination requirements and apply only to welding-end and threaded-end valves, never to flanged-end valves.
Objections, and what holds up
"Class 300 means 300 psi." A frequent shortcut, and wrong. A Group 1.1 Class 300 valve allows 740 psi, about 51 bar, at ambient temperature, and less at higher temperatures.
"A higher class is always the safe choice." It has a higher pressure-temperature rating, but it is not necessarily interchangeable. A flanged Class 600 valve is usually longer face to face than a Class 300 one, in most sizes it does not bolt to Class 300 flanges, and it weighs and costs more.
"The shell test proves the valve can run at the test pressure." Under ASME B16.34, the shell test is run at no less than 1.5 times the 38 °C rating to prove the body. It is an acceptance test, not an operating limit, and it does not raise the class.
How Loonar helps
RFQ Analysis cross-checks the documents in the package against each other. When the datasheet and the piping class give different pressure classes for the same line, it puts both statements side by side with the page each one came from. Your engineers decide which applies, or raise it with the buyer.
Frequently asked questions
Does Class 300 mean 300 psi?
No. The class is a designation, not a pressure. For carbon steel of material group 1.1 (such as ASTM A105 or A216 WCB) at −29 to 38 °C, Class 300 allows 740 psi, about 51 bar. At higher temperatures the allowable pressure falls.
What is the difference between ANSI 300 and ASME Class 300?
None in practice. The flange and valve standards were published as ANSI B16.5 and B16.34 before ASME became the publisher, and many datasheets still write "ANSI 300". The current reference is ASME B16.5 or B16.34, Class 300.
Is a Class 300 flange the same as a PN flange?
No. Class 300 is sometimes informally compared with PN 50 on nominal pressure, but ASME Class and EN PN designations are not directly interchangeable. European PN flanges to EN 1092-1, such as PN 40 or PN 63, have their own dimensions, bolting and pressure-temperature ratings. Check each against the applicable standard.
Can a valve rated Class 600 be used on a Class 300 line?
Not directly. A flanged Class 600 valve usually has a longer face-to-face length than a Class 300 one under ASME B16.10 and, in most sizes, different flange dimensions and bolting, so it does not fit the same gap in the piping. Using it needs the buyer's agreement and a piping check.
Does the same class give the same pressure for every material?
No. Each class has a rating table for each material group. Materials in different groups have different ratings at the same class and temperature. A substitute material in the same class can therefore have a lower allowable pressure, which has to be checked against the design conditions.